Stainless steel mesh with the tightness of the chain should be how to master

Stainless steel wire mesh with a variety of chain type stainless steel mesh belt is used in the daily life of a kind of more extensive, other herringbone stainless steel mesh belt, stainless steel mesh belt, eyes stainless steel mesh belt, etc according to the actual requirements to add the chain, and the role of the chain is to transport in the process of running deviation phenomenon will not occur. So, how should the tightness of the chain of stainless steel mesh belt be mastered? We can use scheduling spanner each time to have 90 degrees of cragging scheduling; It is ok to adjust to the appropriate tightness, which can adhere to a good consistency. What we need to pay attention to is that in the adjustment, we should remember to appropriately loose some of the best. Because, when tightening the rear axle bolt, it will be further tighter than when loosening it! In addition, assuming that the stainless steel chain is a little too tight, it is ok to loosen the same Angle of the bolts at both ends with a wrench, and the best is to step up to 90 degrees, after loosening the bolts, and try to see if the tightness of the stainless steel chain is almost the same. Stainless steel mesh belt chain tightness of the primary scheduling method is these, we must according to the description of reasonable adjustment, as long as so ability to make its function is fully displayed, bring us higher efficiency of operation.

Why is the stainless steel mesh belt also rusty?

When the surface of the stainless steel tube appears brown rust spot (point), people are surprised: think that "stainless steel is not rust, rust is not stainless steel, may be the steel has a problem". In fact, this is the lack of understanding of stainless steel a one-sided wrong view. Stainless steel mesh belt will rust under certain conditions. Stainless steel has the ability to resist atmospheric oxidation - namely, rust, but also has the ability to corrosion in the medium containing acid, alkali, salt - namely, corrosion resistance. However, its corrosion resistance varies with its chemical composition, mutual state, service conditions and environmental media types. Such as 304 steel pipe, in the dry and clean atmosphere, there is absolutely excellent corrosion resistance, but it will be moved to the coastal area, in the sea fog containing a lot of salt, will soon rust; And 316 steel pipe is good performance. Therefore, not any kind of stainless steel, in any environment can withstand corrosion, not rust. Stainless steel is formed by its surface of a layer of very thin and solid fine stable chromium oxide film (protective film), to prevent oxygen atoms continue to penetrate, continue to oxidize, and obtain the ability to resist corrosion. Once for some reason, this film is continuously damaged, oxygen in the air or liquid will continue to infiltrate or iron atoms in the metal is constantly removed, the formation of loose iron oxide, the gold surface is also subjected to continuous corrosion. This surface film is damaged in many forms, common in daily life are as follows: 1 stainless steel mesh belt surface deposit containing other metal elements of dust or different metal particles attached, in the humid air, the condensate between the attachment a

Metal mesh belt bearing fault identification method

The fault identification method of metal mesh belt bearing is as follows: 1) Sample and analyze the smoothing agent through identification of the state of lubricant, and determine whether the dirty level is mixed with foreign matter or metal powder. This method is particularly effective for bearings or large bearings that cannot be inspected closely. Metal mesh belt 2) Recognition by voice Recognition by voice requires substantial experience. It must be possible to distinguish bearing sounds from non-bearing sounds through adequate practice. To this end, should be as far as possible by the person to carry out this work. The sound of the bearing can be clearly heard by using a listener or a listening stick attached to the housing. 3) Identification by working temperature this method is a comparison identification method, limited to use in the operation of the situation does not change much. To this end, the glasses mesh belt, the continuous temperature record must be carried out. In the event of failure, not only the temperature rises, but also irregular changes emerge.

Application of stainless steel mesh belt in food industry

Stainless steel mesh belt in stainless steel food stainless steel mesh belt (food stainless steel mesh belt material 316 and 304 difference one) industry is a convenient, flexible, good air permeability, high temperature resistance, corrosion resistance, smooth operation, high processing accuracy, not easy to run off, long life. Is widely used in the food industry chocolate, biscuit baking, frozen vegetable dehydration, drying; Application of it, the material can be in a certain conveying line, from the initial feeding point to the final unloading point between the formation of a material conveying process. It can not only carry out the transportation of broken materials, but also can carry out the transportation of articles. In addition to pure material transportation, but also with the production process of industrial enterprises in the process of the requirements of the process, the formation of a rhythmic flow line transport. Stainless steel mesh belt is mainly used in the food industry and food machinery industry, is a friction drive to transport materials in a continuous way of machinery. The application of food stainless steel mesh belt, the material can be in a certain conveyor line, from the initial feeding point to the final unloading point between the formation of a material conveying process. It can not only carry out the transportation of broken materials, but also can carry out the transportation of articles. In addition to pure material transportation, but also with the production process of industrial enterprises in the process of the requirements of the process, the formation of a rhythmic flow line transport. So stainless steel mesh belt is widely used in various modern industrial enterprises. It is an essential part of automatic devices and modern automatic assembly lines in all industries.

Stainless steel mesh belt elongated reasons

In industrial production, material transportation is more common, the process of using the net belt, the net belt will be elongated, then, the stainless steel net belt can be retracted after using elongation? In fact, stainless steel mesh belt in the process of use, part of which belongs to the elastic elongation, after the external force is removed can be restored to original state, but long continuous use, will inevitably make the net belt some extensibility, and the elongation is not back. Stainless steel mesh belt The amount of extension and the quality of the network belt has an inseparable relationship, so it is very important to choose a good quality network belt, whether it is for the use of time or production efficiency has a great auxiliary role. Light mesh belt, the general service life of 2-3 years, of course, if the maintenance is better, the use time will be longer. Therefore, in the process of use, the amount of stainless steel mesh belt can shrink back is much smaller than the elongation.

The safe use of stainless steel mesh chain?

Stainless steel mesh chain is a friction drive to transport materials in a continuous way of machinery. Application of it, the material can be in a certain conveying line, from the beginning of the feeding point to the end of the unloading point between the formation of a material conveying process. It can not only carry out the transportation of broken materials, but also can carry out the transportation of articles. In addition to pure material transportation, but also with the production process of industrial enterprises in the process of the requirements of the process, the formation of a rhythmic flow line transport. Therefore, metal mesh belt is widely used in various modern industrial enterprises. It is an essential part of automatic devices and modern automatic assembly lines in all industries. Do you know the safe use of stainless steel mesh chain? The following is a detailed answer by xiaobian. Hope to be of some help to you. Stainless steel mesh chain should be stored in a dry environment to avoid damp motor. Stainless steel mesh chain in the open storage, there should be rain proof measures. In the process of storage and handling should prevent the stainless steel mesh chain knock, so as not to damage the stainless steel mesh belt. The use of stainless steel network chain environment should always keep clean, stainless steel network chain surface to keep clean, inlet and outlet should not have debris. Regularly eliminate stainless steel mesh chain and pipe dust and other sundries. According to the use of environmental conditions of bearings to supplement or replace the lubricating grease, in order to ensure good lubrication of stainless steel mesh chain in the process of operation, the number of refueling is not less than 1000 hours/time, closed bearings and motor bearings, refueling with ZL-3 lithium lubricating grease filling bearing inner and outer ring 2/3, is strictly prohibited from running without oil.

Analysis of reasons for broken wire of stainless steel mesh belt

1. Improper adjustment of the head size will lead to disorder of the normal compression ratio, resulting in wire breakage in the weaving process. The solution is to ensure the absolute size of the die on the machine. 2. Oil or water is cut off in the process of mold operation, resulting in short operation with large hole spacing and unbalanced compression ratio, thus breaking the line. The solution was to add lubricant to each mould in time to ensure cooling and lubrication.

How is the stainless steel mesh belt sprayed

Stainless steel mesh belt has now become the leader of the transport profession, loved by a wide range of users, the network belt in the process of use must do a good job in the corresponding spraying operation, as long as it can better protect it, so what is the spraying method of stainless steel mesh belt first, let's specific understanding. The pretreatment of stainless steel mesh belt, in order to make the film adhesion is strong, not easy to fall off, long life, spraying before the appearance of the stainless steel mesh belt pretreatment. Coating is dry according to its properties of paint physical dry and chemical dry. The pretreatment of the Great Wall net belt is very bond, spraying is also a process of demand, divided into three processes, the first advance predecessors line pretreatment, and then spraying, and finally to dry. The order of the three processes is not interchangeable. There are more than ten kinds of coatings, such as grease coatings, natural resins, epoxy resins, phenolic resins, etc., which can be selected according to the practice.

how to use mesh conveyors

Before the operation of the net belt conveyor, it is necessary to confirm that the equipment, personnel and transported items of the net belt conveyor are in a safe and sound state; Secondly, check the normal movement of the parts, check whether all the electrical lines are normal, normal can be put into operation belt conveyor. Finally, check that the difference between the supply voltage and the rated voltage of the equipment is no more than ±5%. The specific operation of the net belt conveyor is as follows: 1. Close the general power switch and check whether the power supply of the equipment is normally fed and whether the power indicator is on. Go to the next step. 2. Switch on the power switches of each circuit to check whether the circuit is normal. In the normal state, the equipment does not work, the operation indicator light of the net belt conveyor is not on, the power indicator light of the inverter and other equipment is on, and the display panel of the inverter is normal. 3. Start each electrical device in turn according to the process flow. Start the next electrical device after the previous one starts normally.

how conveyor belt works?

With the development of economic level, the conveyor belt has been widely used, showing in many handling scenes, such as the goods in and out of the warehouse of large storage, the production line of enterprises, the handling of goods at the dock and so on. The conveyor belt can carry and transport goods well, and its effect is convenient and remarkable. It and the transmission device together constitute the transmission system, which brings a lot of convenience in our life. Today, we will tell you about the working principle of the conveyor belt. The working principle of the conveyor belt is as follows: the driving device tightens the conveyor belt, the middle frame and the idler. When the driving device works, it drives the operation of the rotating shaft, thus driving the operation of the idler. The idler drives the circular rotation of the conveyor belt through friction, so as to achieve the effect of transportation. From the working principle, the conveyor belt is relying on the friction power and operation, so no matter how we maintain, its friction must still have, but master the correct operation method and maintenance skills, so as to reduce the wear produced by the conveyor belt friction. Therefore, in daily use, we must pay attention to the accuracy and tightness of the installation of the conveyor belt;

Seven advantages of stainless steel mesh chain?

Stainless steel mesh chain can be used 201 or 202 sections of nickel material, with the chain drive, so that the force of the mesh converyor belt is reduced, prolong the use cycle, transform the width of the mesh strip, you can install all kinds of chain, easy to install the accessories of the mesh converyor belt, such as baffle, wings, used for conveying solid materials, good permeability, easy to clean. The material is made of SUS304 316 and other high corrosion resistant materials, which are used in the assembly line of the food industry. It is safe and hygienic. The specifications are generally assembled by 08B chains, which are easy to replace and maintain. Stainless steel mesh chain also known as metal mesh, stainless steel mesh)

When the chain plate rust phenomenon need to solve?

Chain plate application in various industries, all chain plate is likely to rust, so this phenomenon, how should we solve it? 1. we must often clean the appearance of the equipment chain board, remove attachments, eliminate external factors in the process of use. 2. Chain plate made of 316 material should be used in seaside areas, which can resist corrosion of sea water. Three, the chemical composition of some stainless steel chain plate on the market can not match the response to China's standards, can not meet the requirements of 304 material. Therefore, it will also cause rust, which is necessary for users to carefully choose the products of reputable manufacturers. Hope the above information can help you, later will update more knowledge about the chain board, please look forward to it!

Five ways to clean your network chain conveyor?

With the continuous development of automation, network chain is conveying machinery, drying machinery, cleaning machinery and other automatic equipment indispensable important parts. Stainless steel mesh chain can be selected according to the conveying materials and process requirements, to meet the different needs of all walks of life. Network chain in the longer use process will inevitably be mixed with some of the residue of conveying materials, it is difficult to clean, especially the stainless steel network chain in food machinery, a long time will also produce pollution to food, cleaning network chain five methods do you know? Let's have a detailed understanding of it. 1, high pressure spray cleaning mainly depends on the effect of high pressure water attack from the nozzle, so that the dirt attached to the surface of the stainless steel mesh chain is removed. 2, bubble cleaning method is to make the air into the water, constantly stirring the clean water and attack a large number of bubbles, the cavitation effect of the attack on the surface of the cleaned objects, so that the washed objects are clean and clean. 3, brush cleaning method is through the direct touch of the bristles and the water material, so that the dirt on the surface of the material can be brushed and cleaned. 4, the lower part of the drum conflict cleaning drum sink in the water, the material is placed in the sieve drum, because of the rolling effect of the drum, so that the conflict between the material and the material and the drum, so that the material surface soil removed and clean. 5, ultrasonic cleaning method is in the liquid attack millions of small vacuum bubbles, these bubbles under the effect of sound pressure rapidly a large number of attacks, and constantly strong explosion, a strong pressure and negative pressure suction, so that the dirt from the appearance of the object, on the clean

Stainless steel mesh belt too wide will collapse how to do?

Large dryer used stainless steel mesh belt is generally more than 2 m width, with net belt itself has its own weight, in combined with the weight of the material, the density of it is a good net belt specifications also can appear to middle bending, this is the most common problem and the customer the most concern, today we have come to explain the solution to this problem? 1. Additional wheels can be added according to the environment. (1) the equipment can be fixed on the wheel can be directly used without the wheel frame, stainless steel mesh belt frame on the wheel reciprocating operation. (2) if the equipment can not be fixed on the wheel, you can use the wheel with a frame, the wheel is fixed on the frame, stainless steel mesh belt frame reciprocating operation on the wheel. 2. Guide slots can be used. The guide groove consists of five parts: standard length side guide wall, guide groove connecting Angle steel, mounting screws, bottom groove, sliding device. The sliding device is divided into several: nylon wheel, steel sliding plate, plastic sliding plate. In this way, the guide groove is correspondingly divided into three types: (1) Guide groove with nylon wheel (2) guide groove of strip sliding plate

Wire Belts for Cooling & Freezing Equipment,Bakery Equipment

We specialized to produce wire belts for food industry,include cooling & freezing equipment,bakery equipment,kitchen equipment,ice cream machines,processing lines for meat,dumplings,fishes,shrimps,fruits and vegetables,candies,chocolates and snack foods.Besides,we also provide site installation and commissioning services, and craft consultation services. Our wire mesh belts have been exported to North America,South America, Europe,Australia,Africa,Southeast Asia and the Middle East areas.Our technicians have been sent to Mexico,Canada,Zambia,Costa Rica,United States,South Korea and many other countries for machines`installation and commissioning. We have well-educated sales staff who can communicate with you efficiently by English.We have experienced engineers who can design conveyor belts exactly according to your special requirement.We have well-trained after-sales staff who can listen to your feedback carefully and help you in time if you have any question.

Application Range of Stainless Steel Conveyor Belt

Purpose of stainless steel conveyor belt: it is widely used in glass products industry and food processing industry. Stainless steel conveyor belts are widely used to transport materials in cement, metallurgy, casting, chemical industry and other fields. It can be used as high temperature resistant and burning resistant conveyor belt, stainless steel mesh belt of electronic scale, tear resistant conveyor belt, acid and alkali resistant oil conveyor belt, etc. Application Area: 1. Food and biscuit industry: mesh belt, cooling fuel injector mesh belt, flat bending machine mesh belt, chocolate coating machine B-shaped mesh belt. At the same time, we also produce biscuit machinery, egg sprayer type B mesh belt and meat conveying type B mesh belt, and imported ultra-thin energy-saving mesh belt. 2. Instant noodles and rice flour industry; Steaming mesh belt, frying box, drying hanging box, silk cutter, knife comb, face knife, face comb, support shaft, forming box, etc. 3. Stainless steel flat top chain, chip removal chain, conveying chain, mesh belt, support shaft, etc. for all kinds of quick-frozen food and vegetable dehydration assembly line equipment. 4. Glass products industry: glass annealing furnace mesh belt, baking furnace mesh belt, bottle conveyor mesh belt and mosaic mesh belt, with specifications of crankshaft type, straight axis type, diamond and double strand spiral type. Materials include A3 low carbon steel, dcy13 heat-resistant steel, icy18n19ti steel, oor18ni14moo2cu2 acid and heat-resistant steel, etc. The conveyor belt of high-temperature furnace is generally made of 310S and 314, with high temperature resistance of more than 1100 ℃. 5. Manufacturing all kinds of chain plate turning machines, mesh belt conveyors and metal mesh chain belts. The wire diameter range of spring is 0.25-14mm, including compression spring, torsion spring, tower spring

Chain Conveyor Belt for Freezer Industry in Lebanon

We have established cooperation with this buyer since 2019.Under so long time friendly and satisfied with each other,this cilent booked more than 500 meters order with us.All of these,based on good quality and best service,also those are our company business rules and philosiphy. So now because of our quality and reputation,in the following days,we have a meeting and negotiation with our other customers from Chile and Peru.As soon as any further feedback,we'll announce them here.Thanks very much for all concern.

Cooling Conveyors

The Cooling Conveyors are designed to cool down and transport the baked loaves coming out from baking oven to packaging table. The length of the conveyors depends on the given layout and the available space as well as the type of production line and purpose. Composed of aluminum straight conveyor`s frame and coated steel curves. The width of the cooling conveyors varies to be adequate with the production line. Belts move straight with 90 or 180 degree curves, or as required. The curves of the conveyor are found to be normal or opposed in size and shape. The belts are made with fiber web in a professional way to maintain chain tensions and minimize the stretching of the belt. It is relatively silent in operation. The fixation of the cooling unit could be either on ground spiral form or layered form, or hanged to the ceiling to benefit from the space beneath it. It is controlled via variable speed motors and variable inverter system to control the cooling process from external electric control panel that is mounted either on wall or on stand. The machine can be upgraded; due to demand, to be stainless steel curves frame and stands or to increase cooling process as well as to be equipped with CE safety and protection features.